GBHS Mid-Term Exam for Woods I 2023

Last updated over 3 years ago

50 questions

Note from the author:

1

Draggable item		Corresponding Item
12/16 or 3/4		A
16/16 or 1		B
6/16 or 3/8		C
3/16		d

GBHS Mid-Term Exam for Woods I 2023

GBHS Mid-Term Exam for Woods I 2023

Please give me your first and last name and ID # indicating who you are and that you are infact taking this test.

Please give me your first and last name and ID # indicating who you are and that you are infact taking this test.

Our band saw has two sets of guides.

You must store your project materials in your back pack for safe keeping.

The Planer has a variable feed control?

After applying glue to a project you can remove clamps and machine it after 3 minutes

The Jointer will help to straigten a warped or bowed board?

Our band saw has two drive wheels.

The size of the band saw is determined by the diameter of the wheels.

The Planer will help to straigten a warped or bowed board?

The Band Saw has a variable speed control?

When boring a hole, the larger the drill bit, the faster the drilling speed.

You should not stand to the right side of the band saw while cutting.

Only use safety guards if you are feeling unlucky.

Our drill press has a variable speed control.

The blade on our band saw is tracked "adjusted" on the upper wheel.

Shoes that cover your heels and toes are a type of "PPE" or safety gear that should be worn during open lab

Setting the height of the upper guide and guard on the drill press is not important.

Wood is held against the fence while cutting on the miter saw.

Your fingers should be 1/8” to 1/2” from the blade while cutting on the miter saw.

When changing a blade or making a setup the power to that machine should be disconnected.

Cleanup is the sole the responsibility of the custodians.

Dress is always a safety concern when working in the shop

Always wait for the machine you are using to come to a complete stop before leaving.

The planer feed direction can be reversed.

Properly applied finishes make a project look better and last longer.

The primary purpose of the band saw is to:

For a safe cut, cylindrical or round stock should be placed in a ____ _______ when cutting on the band saw.

The primary purpose of the miter saw is to:

Which size Band Saw blade will cut the smallest curve or circle?

What type of glue must be cleaned up with a chemical cleaner?

The primary purpose of the Jointer is to:

When cutting multiple pieces to the same length on the Miter Saw, the operater should use a _______ ________ to help them make these identical length cuts.

When drilling a hole on the drill press you should_______ the material to the table

Sand Paper can be found in which of the follwoing forms?

Horseplay is unacceptable in the shop because

The number on the back of a piece of sandpaper represents what?

During working labs when is it ok to remove your safety glasses in the wood shop?

The reason(s) you would sand a project are?

One inch is equal to ________ /16ths?

4/16” is equal to?

How many inches are in one foot?

The primary purpose of the Drill Press is to:

What type of glue can be cleaned up with soap and water.

The primary purpose of the Planer is to:

What is the measurement shown below

What is the measurement shown below

What is the picture below showing?

What is the picture below showing?

What is the picture below showing?

Move the fractions around so that they correspond to the correct letter in the ruler.Zero is already done "in red ink" for you.

For a safe cut, cylindrical or round stock should be placed in a ___ when cutting on the band saw.

When cutting multiple pieces to the same length on the Miter Saw, the operater should use a _ __ to help them make these identical length cuts.

Move the fractions around so that they correspond to the correct letter in the ruler.
Zero is already done "in red ink" for you.