To wear proper PPE at all times in the shop.
To work in the shop wearing sandals.
To ask if you are not sure about using a tool.
Using a tool you have not been trained on.
Running in the shop.
Wearing ear plugs/muffs if working in an environment where noise levels are excessively high for extended periods of time.
Tying long hair back when working in the shop.
Wearing jewelry while working in the shop.
Utilizing the PASS method if you have to use a fire extinguisher.
Cleaning up your work area.
Report an accident to the instructor immediately.
Put all tools in the proper storage place when not in use.
Take safety glasses off when you are too hot.
Leaving scrap materials and clutter around your work area.
Be respectful at all times in the shop.
Measuring tools are used to determine linear measurements. (Length, Width, Area)
Combinations tapes should be used to determine how high the ceiling is.
Ripsaw are used for cutting across the grain of wood
Crosscut are used for cutting across the grain of wood
A Smooth is the smallest planes that can be used with one hand.
A mallet should be used to strike the handle of a chisel.
The term Boring is used for hole 1/4 inch and smaller.
Hammers are only to be used to drive and remove nails
Using the incorrect size screwdriver can provide leverage.
Leave tools pluged in during inspecting and making adjustments.
When working with electric tools, you shouldn't work on a wet surface. You should clean it up and wait for it to dry.
Statinary power tools are to be anchored to the floor.
Powertools are allowed to be used without a guard or shield.
If a power tool cord is bend or broken, you should continue to use it.
Batteries can be charges with different manufacturer chargers, if they fit.
When tightening a Portable Drill, you only use your hands to tighten the chuck.
When using a Portable Drill, you must clamp or vise your piece of work.
When using a Portable Drill, it is acceptable to use dulled bits.
When using a Portable Circular Saw, the blade needs to be adjusted to the correct depth before cutting.
When using a Portable Circular Saw, you should pull the blade way from the wood before turning it on.
When using a Portable Circular Saw, make sure to check the blade pass zone to free of obstacles before cutting.
When using a Reciprocating Saw, only use when it is diffcult to use a circular saw.
When using a Reciprocating Saw, make sure the speed of the blade is going slow enough before cutting.
When using a Band Saw, should not be anchored to the floor.
When using a Band Saw, a wider blade cuts shape curves.
When using a Band Saw, before pluging in, you should check the teeth are pointing down and the band is tight.
When using a Table Saw, the rip fence should be placed to unsure straight cuts.
When using a Table Saw, you should use your hand to push narrow and short pieces when making a cut.
When using a Table Saw, you should stand to the side of the blade and do not reach across the table.
When using a Table Saw, you should never clean up the sawbust.
When using a Shapers, make sure to check all adjustments and locking nuts before using the machine.
When using a Shapers, make sure to feed the wood in the correct direction using the proper guards and clamps.
When using a Jointer, you will be cutting bevels for chamfers within a piece of wood.
When using a Shapers, make sure the piece is free of knots and splits.
When securing a piece of wood, you should use your hand as a vise.
To make sure your cuts are precise, you should use a Miter Box with a handsaw.
When cutting with a hand saw, use your index finger to improve your control.
When crosscutting a board, you should hold the blade at a 45 degree angle.
When ripping a board, you should hold the blade at a 45 degree angle.
When finish cutting a board, you should return all material, equipment and clean up your space.
The most comman blade using for a Power Saw is a Combination Blade.
When replacing the blade on a Power Saw, you should follow the manufactures instructions localed in the file cabniet.
When positing a board to be cut, the board should be place where the board will not splinter or the blade will cut something unexpected.
When finished using a power saw, you should clean up the area and unplug the equipment.
To make sure the stock doesn't spilt when Boring, you should drill from both sides or place a piece of wood behind the stock.
When fastening to wood, you should hold the nail head toward the bottom of the nail.
When fastening a nail, you should slowly hammer at first then drive the nail.
Before fastening screws into wood, you much make a pilot or shank hole.