{{asɛmtiNe Ɔkyerɛwfo}} | Nhomakorabea | Nneɛma a ɛma wotumi yɛ ade

1

What is the proper order for adding sensors?

Tamper --> Learn --> Label

Tamper --> Label --> Learn

Learn --> Label --> Tamper

Learn --> Tamper --> Label

1

What does a Yellow Status indicator light mean?

Non - Urgent System Condition

Urgent System Condition

System is ready

None of the above

1

How many methods are there to add a camera to the Ultrasync Hub ?

2

3

4

5

1

What is the maximum amount of sensors that can be added to the panel?

32

64

100

256

1

When will the system be able to Arm ?

When at least one sensor is ready

When All sensors are ready with not ready sensors bypassed

When All sensors are ready with not ready sensors not bypassed

When no sensor is ready

1

How many ways can you arm/ disarm the panel?

1

2

3

4

1

What is the maximum number of user profiles that the UltraSync Hub can facilitate?

10

50

100

256

1

What is the maximum distance between door sensor and magnet for proper operation?

Less than 1/2 inch

less than 3/4 inch

Less than 1 inch

None of the above

1

What is the default IP address of the Panel when in WiFi discovery mode?

192.168.100.1

192.168.1.3

192.168.1.1

192.168.1.11

1

What is the default installer access PIN?

1234

1921

0000

9713

1

How long does the cameras take to boot once powered?

1 minute

2 - 3 minutes

5 minutes

8 - 10 minutes

1

Which of the following can trigger a smoke alarm based on its mechanism of operation?

Smoke

Dust

Cooking Fumes

All of the Above

1

What is the maximum amount of digits allowed when changing the Web Access Passcode?

4

8

16

24

1

When the panel is connected via Ethernet cable but still has no internet access, which of these may be the possible reasons?

Router on but no internet connection

Defective Cable wire

Defective RJ-45 Jack

All of the above

1

By default, what happens when the armed away button is pressed on the panel?

Prompted to Enter User Pin

Entry Exit Delay begins

Panel Arms Instantly

Alarm Siren Turn on

1

Why would the panel have a cellular link fault?

APN not configured

Low cell signal strength in the area

No SIM card in Cellular module

All of the above

1

What is correct sequence to Factory Reset an Ultrasync Panel ?

Menu ---> 9 ---> installer pin ---> Bypass

Menu ---> 9 ---> installer pin ---> 0 ---> Bypass

Menu ---> 2 ---> installer pin ---> Menu

Menu ---> 7 ---> installer pin ---> 2 ---> Bypass

1

When is an installer allowed to leave the Tamper option on the Motion Sensor off ?

If they know the sensor has been installed incorrectly

If the sensor is defective

If the sensor is not in close proximity to the panel.

None of the above.

1

What frequency to the interlogix sensors operate with?

2.4 GHz

319.5 MHz

320 MHz

800 MHz

1

Where can the default pass code for the camera broadcasting Wi-Fi be found?

Camera Label

Camera Box

Camera's Broadcasting Wi-Fi SSID

All of the above

C1S3

C1S3

What is the proper order for adding sensors?

What does a Yellow Status indicator light mean?

How many methods are there to add a camera to the Ultrasync Hub ?

What is the maximum amount of sensors that can be added to the panel?

When will the system be able to Arm ?

How many ways can you arm/ disarm the panel?

What is the maximum number of user profiles that the UltraSync Hub can facilitate?

What is the maximum distance between door sensor and magnet for proper operation?

What is the default IP address of the Panel when in WiFi discovery mode?

What is the default installer access PIN?

How long does the cameras take to boot once powered?

Which of the following can trigger a smoke alarm based on its mechanism of operation?

What is the maximum amount of digits allowed when changing the Web Access Passcode?

When the panel is connected via Ethernet cable but still has no internet access, which of these may be the possible reasons?

By default, what happens when the armed away button is pressed on the panel?

Why would the panel have a cellular link fault?

What is correct sequence to Factory Reset an Ultrasync Panel ?

When is an installer allowed to leave the Tamper option on the Motion Sensor off ?

What frequency to the interlogix sensors operate with?

Where can the default pass code for the camera broadcasting Wi-Fi be found?

What is the proper order for adding sensors?

What does a Yellow Status indicator light mean?

How many methods are there to add a camera to the Ultrasync Hub ?

What is the maximum amount of sensors that can be added to the panel?

When will the system be able to Arm ?

How many ways can you arm/ disarm the panel?

What is the maximum number of user profiles that the UltraSync Hub can facilitate?

What is the maximum distance between door sensor and magnet for proper operation?

What is the default IP address of the Panel when in WiFi discovery mode?

What is the default installer access PIN?

How long does the cameras take to boot once powered?

Which of the following can trigger a smoke alarm based on its mechanism of operation?

What is the maximum amount of digits allowed when changing the Web Access Passcode?

When the panel is connected via Ethernet cable but still has no internet access, which of these may be the possible reasons?

By default, what happens when the armed away button is pressed on the panel?

Why would the panel have a cellular link fault?

What is correct sequence to Factory Reset an Ultrasync Panel ?

When is an installer allowed to leave the Tamper option on the Motion Sensor off ?

What frequency to the interlogix sensors operate with?

Where can the default pass code for the camera broadcasting Wi-Fi be found?