{{asɛmtiNe Ɔkyerɛwfo}} | Nhomakorabea | Nneɛma a ɛma wotumi yɛ ade

1

Why does the Web Access Passcode need to changed upon setup?

To obtain an IP address

To allow live playback of cameras

To enable remote access

All of the above

1

What is the principle of operation of the Interlogix PIR motion sensor?

Ultra Sound

Optical

Magnetic

Infrared

1

What does a Yellow Status indicator light mean?

Non Urgent System Condition

Urgent System Condition

System is ready

None of the above

1

How many methods are there to add a camera to the Ultrasync Hub ?

2

3

4

5

1

Where can the default passcode for the camera broadcasting Wi-Fi be found?

Camera Label

Camera Box

Camera's Broadcasting Wi-Fi SSID

All of the above

1

What is the maximum height of mounting a PIR indoor motion sensor?

6 feet

7.5 feet

10 feet

15 feet

1

What can be done to improve camera connectivity?

Increase internet bandwidth

Increase internet signal strength

Use Ethernet cable between the camera and router

All of the above

1

What is the maximum number of user profiles that the UltraSync Hub can facilitate?

10

50

100

256

1

What is the maximum number of automation scenes that can be created?

16

20

50

100

1

How long to tamper a flood sensor for it to be added as a flood sensor and not freeze sensor?

Less than 1 second

Between 2-3 seconds

5 seconds

10 seconds

1

How long does it take for the APN to be registered once set?

1 Minute

5 Minutes

10 Minutes

1 Hour

1

How to change installer pin once the install is complete?

Open Site on UltraSync App as an installer - Menu Tab - Select Change PIN

Open Site on UltraSync App as an installer - Menu Tab - Settings - Change PIN

Open Site as User - Menu - Users - Change User PIN

Open Site as User - Menu - Settings - Change User PIN

1

What is the maximum amount of digits allowed when changing the Web Access Passcode?

4

8

16

24

1

Where can WiFi discovery mode be found?

Advanced settings on the panel menu [ menu - 9]

Basic Settings on the panel menu [ menu - 8]

All of the above

None of the above

1

What does the panel box tamper do?

Tamper the panel to be added into the system

Tamper the panel to be learned into another alarm system

Tamper tester for sensors

Tamper alarm for the panel

1

How to toggle between WiFi and Ethernet Mode?

Menu - 9 - installer pin - 7

Menu - 9 - installer pin - 8

Menu - 8 - installer pin - 7

Menu - 8 - installer pin - 8

1

How many modes of connectivity does the Self contained panel have for communication to the alarm center?

2

3

4

5

1

Where should sensors be mounted?

In proximity to the panel

Away from electronic devices

Away from Moisture

All of the above

1

What does the sensor notification button on the sensor Tab do?

Enables audible chime on the panel

Enables History on the Panel

Bypasses the sensor

None of the above

1

What is the default IP address of the Bullet Camera when its in WiFi discovery mode?

192.168.2.70

192.268.100.1

192.168.2.1

192.168.2.0

C1S4

C1S4

Why does the Web Access Passcode need to changed upon setup?

What is the principle of operation of the Interlogix PIR motion sensor?

What does a Yellow Status indicator light mean?

How many methods are there to add a camera to the Ultrasync Hub ?

Where can the default passcode for the camera broadcasting Wi-Fi be found?

What is the maximum height of mounting a PIR indoor motion sensor?

What can be done to improve camera connectivity?

What is the maximum number of user profiles that the UltraSync Hub can facilitate?

What is the maximum number of automation scenes that can be created?

How long to tamper a flood sensor for it to be added as a flood sensor and not freeze sensor?

How long does it take for the APN to be registered once set?

How to change installer pin once the install is complete?

What is the maximum amount of digits allowed when changing the Web Access Passcode?

Where can WiFi discovery mode be found?

What does the panel box tamper do?

How to toggle between WiFi and Ethernet Mode?

How many modes of connectivity does the Self contained panel have for communication to the alarm center?

Where should sensors be mounted?

What does the sensor notification button on the sensor Tab do?

What is the default IP address of the Bullet Camera when its in WiFi discovery mode?

Why does the Web Access Passcode need to changed upon setup?

What is the principle of operation of the Interlogix PIR motion sensor?

What does a Yellow Status indicator light mean?

How many methods are there to add a camera to the Ultrasync Hub ?

Where can the default passcode for the camera broadcasting Wi-Fi be found?

What is the maximum height of mounting a PIR indoor motion sensor?

What can be done to improve camera connectivity?

What is the maximum number of user profiles that the UltraSync Hub can facilitate?

What is the maximum number of automation scenes that can be created?

How long to tamper a flood sensor for it to be added as a flood sensor and not freeze sensor?

How long does it take for the APN to be registered once set?

How to change installer pin once the install is complete?

What is the maximum amount of digits allowed when changing the Web Access Passcode?

Where can WiFi discovery mode be found?

What does the panel box tamper do?

How to toggle between WiFi and Ethernet Mode?

How many modes of connectivity does the Self contained panel have for communication to the alarm center?

Where should sensors be mounted?

What does the sensor notification button on the sensor Tab do?

What is the default IP address of the Bullet Camera when its in WiFi discovery mode?