Lesson 8.7 Woodworking

1

When using a handsaw, the blade used for Crosscuting should have 8-10 points

1

When using a handsaw, the blade used for General Use should have 8-10 points

1

When using a handsaw, the blade used for Fine Cut should have 11-12 points

1

When securing a piece of wood, you should use your hand as a vise.

1

To make sure your cuts are precise, you should use a Miter Box with a handsaw.

1

When cutting with a hand saw, use your index finger to improve your control.

1

When crosscutting a board, you should hold the blade at a 45 degree angle.

1

When ripping a board, you should hold the blade at a 45 degree angle.

1

When finish cutting a board, you should return all material, equipment and clean up your space.

1

The most comman blade using for a Power Saw is a Combination Blade.

1

When replacing the blade on a Power Saw, you should follow the manufactures instructions localed in the file cabniet.

1

When positing a board to be cut, the board should be place where the board will not splinter or the blade will cut something unexpected.

1

When finished using a power saw, you should clean up the area and unplug the equipment.

1

The most comman and new bit to use is called a Twist Bit.

1

When wating to make a hole partly through the stack, you should use a Forstner Bit.

1

When wanting to make a rounded bottom with using a bit, you should use a Spade or Speed Bit.

1

When boring with a drill, you should make sure the drill bit is secured using your hand strength.

1

When drilling into a stock, the stock should be placed into a vice or clamp.

1

To make sure the stock doesn't spilt when Boring, you should drill from both sides or place a piece of wood behind the stock.

1

When framing a wood sturcture, you should use Box Nails

1

Finishing Nails have a small rounded head best used for Cabinetwork or Trim.

1

Nails with large flat headeds are called Roofing Nails.

1

Duplex Nails have a two staging heads for temporary uses.

1

To have a strong nailing, you should use a Clinched or Toe Nailed fasting method.

1

When fastening to wood, you should hold the nail head toward the bottom of the nail.

1

When fastening a nail, you should slowly hammer at first then drive the nail.

1

Steal Screws have a shank that is nonthreaded.

1

Lesson 8.7 Woodworking

When using a handsaw, the blade used for Crosscuting should have 8-10 points

When using a handsaw, the blade used for General Use should have 8-10 points

When using a handsaw, the blade used for Fine Cut should have 11-12 points

When securing a piece of wood, you should use your hand as a vise.

To make sure your cuts are precise, you should use a Miter Box with a handsaw.

When cutting with a hand saw, use your index finger to improve your control.

When crosscutting a board, you should hold the blade at a 45 degree angle.

When ripping a board, you should hold the blade at a 45 degree angle.

When finish cutting a board, you should return all material, equipment and clean up your space.

The most comman blade using for a Power Saw is a Combination Blade.

When replacing the blade on a Power Saw, you should follow the manufactures instructions localed in the file cabniet.

When positing a board to be cut, the board should be place where the board will not splinter or the blade will cut something unexpected.

When finished using a power saw, you should clean up the area and unplug the equipment.

The most comman and new bit to use is called a Twist Bit.

When wating to make a hole partly through the stack, you should use a Forstner Bit.

When wanting to make a rounded bottom with using a bit, you should use a Spade or Speed Bit.

When boring with a drill, you should make sure the drill bit is secured using your hand strength.

When drilling into a stock, the stock should be placed into a vice or clamp.

To make sure the stock doesn't spilt when Boring, you should drill from both sides or place a piece of wood behind the stock.

When framing a wood sturcture, you should use Box Nails

Finishing Nails have a small rounded head best used for Cabinetwork or Trim.

Nails with large flat headeds are called Roofing Nails.

Duplex Nails have a two staging heads for temporary uses.

To have a strong nailing, you should use a Clinched or Toe Nailed fasting method.

When fastening to wood, you should hold the nail head toward the bottom of the nail.

When fastening a nail, you should slowly hammer at first then drive the nail.

Steal Screws have a shank that is nonthreaded.

Before fastening screws into wood, you much make a pilot or shank hole.

When using a handsaw, the blade used for Crosscuting should have 8-10 points

When using a handsaw, the blade used for General Use should have 8-10 points

When using a handsaw, the blade used for Fine Cut should have 11-12 points

When securing a piece of wood, you should use your hand as a vise.

To make sure your cuts are precise, you should use a Miter Box with a handsaw.

When cutting with a hand saw, use your index finger to improve your control.

When crosscutting a board, you should hold the blade at a 45 degree angle.

When ripping a board, you should hold the blade at a 45 degree angle.

When finish cutting a board, you should return all material, equipment and clean up your space.

The most comman blade using for a Power Saw is a Combination Blade.

When replacing the blade on a Power Saw, you should follow the manufactures instructions localed in the file cabniet.

When positing a board to be cut, the board should be place where the board will not splinter or the blade will cut something unexpected.

When finished using a power saw, you should clean up the area and unplug the equipment.

The most comman and new bit to use is called a Twist Bit.

When wating to make a hole partly through the stack, you should use a Forstner Bit.

When wanting to make a rounded bottom with using a bit, you should use a Spade or Speed Bit.

When boring with a drill, you should make sure the drill bit is secured using your hand strength.

When drilling into a stock, the stock should be placed into a vice or clamp.

To make sure the stock doesn't spilt when Boring, you should drill from both sides or place a piece of wood behind the stock.

When framing a wood sturcture, you should use Box Nails

Finishing Nails have a small rounded head best used for Cabinetwork or Trim.

Nails with large flat headeds are called Roofing Nails.

Duplex Nails have a two staging heads for temporary uses.

To have a strong nailing, you should use a Clinched or Toe Nailed fasting method.

When fastening to wood, you should hold the nail head toward the bottom of the nail.

When fastening a nail, you should slowly hammer at first then drive the nail.

Steal Screws have a shank that is nonthreaded.

Before fastening screws into wood, you much make a pilot or shank hole.