GBHS Mid-TermExam Woods I 2022 new

1

Please give me your first and last name and ID # indicating who you are and that you are infact taking this test.

1

Our band saw has two sets of guides.

True

False

1

Our band saw has two DRIVE wheels.

True

False

1

You must store your project materials in your back pack for safe keeping.

True

False

1

What does the number on the back of the sandpaper represent?

the date the paper was made

all of these

the cost of the paper

coarseness or the grit

1

Sand paper can be found in which of the following forms?

belt

all of these

sheet

spindle

1

What would be the best choice to finish sand with?

50 grit

80 grit

120 grit

220 grit

1

The size of the band saw is determined by the diameter of the wheels.

True

False

1

A 3/4“ band saw blade will cut tighter circles than a ¼” blade.

True

False

1

When boring a hole, the larger the drill bit, the faster the drilling speed.

True

False

1

You should not stand to the right side of the band saw while cutting.

True

False

1

Only use safety guards if you are feeling unlucky.

True

False

1

Our drill press has a variable speed control.

True

False

1

The blade on our band saw is tracked "adjusted" on the upper wheel.

True

False

1

Shoes that cover your toes and heels are a type of PPE.

True

False

1

What type of glue was used on our first project

Type 1

Type 2

Type 3

1

Wood is held against the fence while cutting on the miter saw.

True

False

1

Your fingers should be 1/8” to 1/2” from the blade while cutting on the miter saw.

True

False

1

When changing a blade or making a setup the power to that machine should be disconnected.

True

False

1

You are responsible for your own safety and the safety of others in the shop.

True

False

1

Cleanup is the sole the responsibility of the custodians.

True

False

1

Use of drugs, alcohol and some medicines can cause accidents while the person is under the influence and operating the machines.

True

False

1

Dress is always a safety concern when working in the shop

True

False

1

Always wait for the machine you are using to come to a complete stop before leaving.

True

False

1

Used oil based finishing rags are flammable.

True

False

1

Properly applied finishes make a project look better and last longer.

True

False

1

The primary purpose of the band saw is to:

Plane boards to thickness

Make rip cuts

Make irregular "curved" cuts

Make Crosscuts

1

The primary purpose of the miter saw is to:

Plane boards to thickness

Make crosscuts

Make rip cuts

Make irregular cuts

1

When drilling a hole on the drill press you should_______ the material to the table

Clamp

Float

None of the these

Glue

1

Horseplay is unacceptable in the shop because

It is distracting to the teacher

It is distracting to fellow students

All of the these

You may not be under control

1

During working labs when is it ok to remove your safety glasses in the wood shop?

When there are no machines turned on

Never

Whenever you want

If you are sitting at a table

1

One inch is equal to ________ /16ths?

9

12

4

16

1

4/16” is equal to?

3/4"

1/8"

4/8"

1/4"

1

In the woodshop we most commonly measure using which units of measures?

Yards, miles, kilometers

Meters, centimeters, millimeters

All of the these

Inches, feet, 16ths of an inch

1

How many inches are in one foot?

24

12

36

10

1

How many inches are in one yard?

24

10

36

12

1

The primary purpose of the Drill Press is to:

Cut of the edge of a board

Sink a screw into  a board

Press one board into another

Bore a hole 

Required

1

What is the measurement shown below

1 & 1/2"

1 & 3/16"

1 & 1/4"

1/4"

Required

1

What is the measurement shown below

2 & 1/2"

2 & 1/16"

2 & 1/8"

2 & 1/4"

Required

1

What is the measurement shown below

1 & 1/2"

1&1/8"

1 & 3/4"

1 & 11/16"

Required

1

What is the picture below showing?

Band Saw

Spindle Sander

Miter Saw

Drill Press

Required

1

What is the picture below showing?

Miter Saw

Band Saw

Spindle Sander

Dril Press

Required

1

What is the picture below showing?

Miter Saw

Drill Press

Spindle Sander

Band Saw

Required

1

The correct units to represent the amount of material within a common board are

BdFt

LnFt

SqFt

Required

1

The correct units to representamount of material within a demensional good are

BdFt

SqFt

LnFt

Required

1

The correct units to represent amount of material within a sheet good are

SqFt

BdFt

LnFt

Required

1

Choosing the correct formula and determine how much material is being used by selecting the correct answer

A piece of crown molding for you bathroom ceiling is 1” thick by 4” wide by 186” long

15.50 LnFt

1.29 LnFt

186 LnFt

Required

1

Choosing the correct formula and determine how much material is being used by selecting the correct answer

A piece of Walnut wood for a jewelry box top is 2” thick by 9” wide by 18” long

27.00 BdFt

2.25 BdFt

324 BdFt

Required

1

Choosing the correct formula and determine how much material is being used by selecting the correct answer

A piece of OSB to cover a hole in a wall left by an old window is 1” thick by 36” wide by 48” long

1728.00 SqFt

144.00 SqFt

12.00 SqFt

Required

1

The formula for calculating board foot is

T x W x L /144

T x W x L /12

T x W x L 

GBHS Mid-TermExam Woods I 2022 new

Please give me your first and last name and ID # indicating who you are and that you are infact taking this test.

Our band saw has two sets of guides.

Our band saw has two DRIVE wheels.

You must store your project materials in your back pack for safe keeping.

What does the number on the back of the sandpaper represent?

Sand paper can be found in which of the following forms?

What would be the best choice to finish sand with?

The size of the band saw is determined by the diameter of the wheels.

A 3/4“ band saw blade will cut tighter circles than a ¼” blade.

When boring a hole, the larger the drill bit, the faster the drilling speed.

You should not stand to the right side of the band saw while cutting.

Only use safety guards if you are feeling unlucky.

Our drill press has a variable speed control.

The blade on our band saw is tracked "adjusted" on the upper wheel.

Shoes that cover your toes and heels are a type of PPE.

What type of glue was used on our first project

Wood is held against the fence while cutting on the miter saw.

Your fingers should be 1/8” to 1/2” from the blade while cutting on the miter saw.

When changing a blade or making a setup the power to that machine should be disconnected.

You are responsible for your own safety and the safety of others in the shop.

Cleanup is the sole the responsibility of the custodians.

Use of drugs, alcohol and some medicines can cause accidents while the person is under the influence and operating the machines.

Dress is always a safety concern when working in the shop

Always wait for the machine you are using to come to a complete stop before leaving.

Used oil based finishing rags are flammable.

Properly applied finishes make a project look better and last longer.

The primary purpose of the band saw is to:

The primary purpose of the miter saw is to:

When drilling a hole on the drill press you should_______ the material to the table

Horseplay is unacceptable in the shop because

During working labs when is it ok to remove your safety glasses in the wood shop?

One inch is equal to ________ /16ths?

4/16” is equal to?

In the woodshop we most commonly measure using which units of measures?

How many inches are in one foot?

How many inches are in one yard?

The primary purpose of the Drill Press is to:

What is the measurement shown below

What is the measurement shown below

What is the measurement shown below

What is the picture below showing?

What is the picture below showing?

What is the picture below showing?

The correct units to represent the amount of material within a common board are

The correct units to representamount of material within a demensional good are

The correct units to represent amount of material within a sheet good are

Choosing the correct formula and determine how much material is being used by selecting the correct answerA piece of crown molding for you bathroom ceiling is 1” thick by 4” wide by 186” long

Choosing the correct formula and determine how much material is being used by selecting the correct answerA piece of Walnut wood for a jewelry box top is 2” thick by 9” wide by 18” long

Choosing the correct formula and determine how much material is being used by selecting the correct answerA piece of OSB to cover a hole in a wall left by an old window is 1” thick by 36” wide by 48” long

The formula for calculating board foot is

Please give me your first and last name and ID # indicating who you are and that you are infact taking this test.

Our band saw has two sets of guides.

Our band saw has two DRIVE wheels.

You must store your project materials in your back pack for safe keeping.

What does the number on the back of the sandpaper represent?

Sand paper can be found in which of the following forms?

What would be the best choice to finish sand with?

The size of the band saw is determined by the diameter of the wheels.

A 3/4“ band saw blade will cut tighter circles than a ¼” blade.

When boring a hole, the larger the drill bit, the faster the drilling speed.

You should not stand to the right side of the band saw while cutting.

Only use safety guards if you are feeling unlucky.

Our drill press has a variable speed control.

The blade on our band saw is tracked "adjusted" on the upper wheel.

Shoes that cover your toes and heels are a type of PPE.

What type of glue was used on our first project

Wood is held against the fence while cutting on the miter saw.

Your fingers should be 1/8” to 1/2” from the blade while cutting on the miter saw.

When changing a blade or making a setup the power to that machine should be disconnected.

You are responsible for your own safety and the safety of others in the shop.

Cleanup is the sole the responsibility of the custodians.

Use of drugs, alcohol and some medicines can cause accidents while the person is under the influence and operating the machines.

Dress is always a safety concern when working in the shop

Always wait for the machine you are using to come to a complete stop before leaving.

Used oil based finishing rags are flammable.

Properly applied finishes make a project look better and last longer.

The primary purpose of the band saw is to:

The primary purpose of the miter saw is to:

Choosing the correct formula and determine how much material is being used by selecting the correct answer

A piece of crown molding for you bathroom ceiling is 1” thick by 4” wide by 186” long

Choosing the correct formula and determine how much material is being used by selecting the correct answer

A piece of Walnut wood for a jewelry box top is 2” thick by 9” wide by 18” long

Choosing the correct formula and determine how much material is being used by selecting the correct answer

A piece of OSB to cover a hole in a wall left by an old window is 1” thick by 36” wide by 48” long

Choosing the correct formula and determine how much material is being used by selecting the correct answer

A piece of crown molding for you bathroom ceiling is 1” thick by 4” wide by 186” long

Choosing the correct formula and determine how much material is being used by selecting the correct answer

A piece of Walnut wood for a jewelry box top is 2” thick by 9” wide by 18” long

Choosing the correct formula and determine how much material is being used by selecting the correct answer

A piece of OSB to cover a hole in a wall left by an old window is 1” thick by 36” wide by 48” long