Sign up for FREE

GBHS Mid-TermExam Woods I 2023

Last updated over 2 years ago

50 questions

1

Required

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

Required

1

1

1

1

Required

1

1

1

1

Required

1

1

1

1

1

1

1

Required

1

Required

1

Required

1

Required

1

Required

1

Required

1

Required

1

Required

1

Required

1

Question 1

1.

Please give me your first and last name and ID # indicating who you are and that you are infact taking this test.

Question 2

2.

Question 3

3.

Question 4

4.

Question 5

5.

Question 6

6.

Question 7

7.

Question 8

8.

Question 9

9.

Question 10

10.

Question 11

11.

Question 12

12.

Question 13

13.

Question 14

14.

Question 15

15.

Question 16

16.

Question 17

17.

Question 18

18.

Question 19

19.

Question 20

20.

Question 21

21.

Question 22

22.

Question 23

23.

Question 24

24.

Question 25

25.

Question 26

26.

Question 27

27.

Question 28

28.

Question 29

29.

Question 30

30.

Question 31

31.

Question 32

32.

Question 33

33.

Question 34

34.

Question 35

35.

Question 36

36.

Question 37

37.

Question 38

38.

Question 39

39.

Question 40

40.

Question 41

41.

Question 42

42.

Question 43

43.

Question 44

44.

Question 45

45.

Question 46

46.

Question 47

47.

Question 48

48.

Question 49

49.

Question 50

50.

The __________ of the Planer must be adjusted to the thickness of theboard before your begin

Cutterhead

Pressure Bar

Chip Breaker

Table/Bed

  
Our band saw has two sets of guides.

True

False

  
Our band saw has two DRIVE wheels.

True

False

You must store your project materials in your back pack for safe keeping.

True

False

What does the number on the back of the sandpaper represent?

the cost of the paper

the date the paper was made

coarseness or the grit

all of these

Sand paper can be found in which of the following forms?

all of these

belt

sheet

spindle

What would be the best choice to finish sand with?

50 grit

80 grit

120 grit

220 grit

  The size of the band saw is determined by the diameter of the wheels.

True

False

  
A 3/4“ band saw blade will cut tighter circles than a ¼” blade.

True

False

  
When boring a hole, the larger the drill bit, the faster the drilling speed.

True

False

  
You should not stand to the right side of the band saw while cutting.

True

False

  
Only use safety guards if you are feeling unlucky.

True

False

 
Our drill press has a variable speed control.

True

False

 
The blade on our band saw is tracked "adjusted"  on the upper wheel.

True

False

 
Shoes that cover your toes and heels  are a type of PPE.

True

False

What type of glue was used on our first project

Type 1

Type 2

Type 3

 
Wood is held against the fence while cutting on the miter saw.

True

False

 
Your fingers should be 1/8” to 1/2” from the blade while cutting on the miter saw.

True

False

 When changing a blade or making a setup the power to that machine should be disconnected. 

True

False

 
You are responsible for your own safety and the safety of others in the shop.

True

False

 
Cleanup is the sole the responsibility of the custodians.

True

False

 
Use of drugs, alcohol and some medicines can cause accidents while the person is under the influence and operating the machines.

True

False

 
Dress is always a safety concern when working in the shop

True

False

 Always wait for the machine you are using to come to a complete stop before leaving.

True

False

 
Used finishing rags are flammable.

True

False

The Planer requires the use of the _____________ while it is in operation.

Fan

Table Saw

Dust Collector

Extension Cord

 
Properly applied finishes make a project look better and last longer.

True

False

The primary purpose of the band saw is to:

Make rip cuts

Make irregular "curved" cuts

Make Crosscuts

Plane boards to thickness

The primary purpose of the miter saw is to:

Make crosscuts

Plane boards to thickness

Make rip cuts

Make irregular cuts

The ____ on the Jointer must be adjusted for the width of each piece before jointing it.

Infeed Table

Fence

Cutterhead

Outfeed atbel

When drilling a hole on the drill press you should_______ the material to the table

Float

Glue

Clamp

None of the these

Horseplay is unacceptable in the shop because

You may not be under control

It is distracting to fellow students

It is distracting to the teacher

All of the these

During working labs when is it ok to remove your safety glasses in the wood shop?

Never

Whenever you want

If you are sitting at a table

When there are no machines turned on

The Jointer will help Straighten a warped "cupped" board

True

False

One inch is equal to ________ /16ths?

16

9

12

4

4/16” is equal to?

3/4"

4/8"

1/4"

1/8"

In the woodshop we use which system of linear mesurment?

Germanic

Imperial

Metric

Cubic

How many inches are in one foot?

24

12

10

36

How many inches are in one yard?

24

10

36

12

The primary purpose of the Drill Press is to:

Cut of the edge of a board

Press one board into another

Bore a hole 

Sink a screw into  a board

The primary purpose of the Jointer is to:

Correct any physical flaws in a board 

Smooth a board out

Make a board thinner

Create parrallel thicknesses on the board

The primary purpose of the Planer is to:

Correct any physical flaws in a board

Smooth a board out

Make a board thinner

Create parrallel thicknesses on the board

The Planer can be reversed?

True

False

What is the measurement shown below

1 & 3/16"

1/4"

1 & 1/2"

1 & 1/4"

What is the measurement shown below

2 & 1/4"

2 & 1/8"

2 & 1/2"

2 & 1/16"

What is the measurement shown below

1 & 3/4"

1&1/8"

1 & 1/2"

1 & 11/16"

What is the picture below showing?

Miter Saw

Drill Press

Spindle Sander

Band Saw

What is the picture below showing?

Miter Saw

Band Saw

Spindle Sander

Dril Press

What is the picture below showing?

Spindle Sander

Miter Saw

Band Saw

Drill Press